Final Effluent Pump

Quantity : Two (2) units’.
Type : Centrifugal, Wear resistant.
Capacity : 40 m³/hour.
Total head : 30 m
Construction :
• Casing : Stainless steel
• Shaft : Stainless steel
• Impeller : Stainless steel
• Seal : Mechanical
Unit drive : 11 kW/ 15 Hp Teco, Electrim electromotor through pulley and v-belts.
Accessories :
• Discharge pipe to cooling tower 4” dia. Steam pipe sch. 80.
• A selector control switch Non return valve.
Make : Roto Pump, Kew Pump or equivalent
Size : 4” / 3”
Power : 15 Hp

Final Effluent Pump

Iklan

Sludge Pit

1 (one) unit Fat Pit, 3 compartment (1 for suction pump ; 1 for sludge and 1 for condensate sterilizer) below ground level, will be provided and installed to receive sludge centrifuges and condensate sterilizer.
Pump will be self priming with tank and lay on ground position.
Type : Rectangular 3 (three) compartment under ground
Construction : Concrete.
• 1 compartment for pump 1.5m x 6.6m to install roofing 2m height.
• Provided round pit 40mm dia. black pipe hand rail.
Capacity : 60 m³
Dimension : 6.6m x 6.1m x 1.5m.
Accessories : A float switches control. Shelter with spandex 0.5 mm.

Sludge Pit

Sludge Drain Pump

Quantity : Two (2) units’, one (1) unit as standby.
Type : Centrifugal.
Make : Kew or equivalent.
Capacity : 30 m³/hour
Total head : 30 m
Construction :
Casing Stainless steel, Shaft Stainless steel, Impeller Stainless steel, Seal Mechanical, Unit drive 4 kW/ 5.5 Hp Teco, Electrim electromotor through pulley
and V-belts,
Accessories A selector control switch & Non return valve.

Sludge Drain Pump

Sludge Drain Tank

Quantity : One (1) unit.
Type : Steel tank rectangular section.
Capacity : 18 m³
Construction :
The tank would be slope bottom construction Fabricated from 6 mm thick m.s plate of welded construction with m.s channel stiffeners. Tank divided by two (2) compartment Fitted adjustable oil skimming device, for draining skimmed oil into an oil tank for pumping back to the continuous settling.

Sludge Drain Tank

Hot Well Pumps

Quantity : Two (2) units’.
Type : Centrifugal.
Capacity : 20m³ per hour, each.
Total head : 30 m
Speed : 1.450 rpm
Construction :
Casings Cast iron, Impeller Bronze, Shaft Stainless steel, Seal Mechanical, Unit
drive Direct coupling 5,5 kW/ 7,5 Hp Teco, Electrim electromotor on common
base plate and Allen Gwynnes pump.

Hot Well Tank and Pumps

Hot Well Tank

Quantity : One (1) unit.
Type : Rectangular.
Capacity : 3 m³
Construction :
Fabricated from 6 mm thick steel plate of all welded construction. Stiffeners
40x40x4 mm thick m.s steel angle at the top edge. Provided with overflow pipe.
Dimension 1.500 mm x 1.500 mm height.

Hot Water Tank

Quantity : One (1) unit.
Capacity : 6 m³
Type : Rectangular.
Construction :
Fabricated from 6 mm thick m.s plate of all welded construction. Provided with a Manhole provided with suitable 1¼” dia. direct steam ejector to raise the water Temperature to 95 degree C. provided with an inlet, overflow and discharge pipes.
Accessories Thermostatic control valve. A Temperature gauge float valve.

Hot Water Tank